标准编号:	QC/T 1178-2022
中文名称:	汽车和挂车 气压制动系统 螺纹孔和管接头
英文名称:	Motor vehicle and towed vehicle Pneumatic brak ing system Tapped and male fitting
行业分类:	QC    汽车行业标准
发布机构:	中华人民共和国工业和信息化部
发布日期:	2022-04-08
实施日期:	2022-10-1
标准状态:	现行
翻译语言:	英文
文件格式:	PDF
中文字符数:	8000 字
翻译价格(元):	560.00 元
交付时间:	付款后 1~3 个工作日

Attachment:



No., name and implementation date of 45 professional standards of automobiles

S.N. Standard No. Name of standard No. of replaced standard Implementation date

177 QC/T 1157-2022 Method of calculating comprehensive energy consumption for unit output of automobile products 2022-10-01

178 QC/T 1158-2022 Method of calculating comprehensive water consumption for unit output of automobile products 2022-10-01

179 QC/T 1159-2022 Guidelines on evaluation of automobile industry green supply chain management 2022-10-01

180 QC/T 1160-2022 Guidelines on evaluation of whole vehicle manufacturing green factory in automobile industry 2022-10-01

181 QC/T 1161-2022 Technical specifications for green-design product assessment - Automobile 2022-10-01

182 QC/T 1162-2022 Honeycomb sandwich structure product for automobile exterior decoration parts 2022-10-01

183 QC/T 1163-2022 Automotive diesel engines - Reduction agent filter for selective catalytic reduction (SCR) system 2022-10-01

184 QC/T 1164-2022 Natural gas filter for road vehicle 2022-10-01

185 QC/T 1165-2022 Carbon canister air filter for gasoline passenger car 2022-10-01

186 QC/T 1166-2022 Streaming rear-view mirror for vehicle 2022-10-01

187 QC/T 1167-2022 Service brake dynamometer squeal noise test methods for passenger cars 2022-10-01

188 QC/T 1168-2022 Performance requirements and bench test methods for vehicle electric air compressor 2022-10-01

189 QC/T 463-2022 Technical requirements and bench test methods for automotive hydrodynamic torque converter assembly QC/T 29033-1991

QC/T557-1999

QC/T 463-1999 2022-10-01

190 QC/T 792-2022 Motors and controllers for electric motorcycles and electric mopeds QCT 792-2007 2022-10-01

191 QC/T 1169-2022 Liquid crystal instrument for automobile 2022-10-01

192 QC/T 1170-2022 Performance film for automotive glass 2022-10-01

193 QC/T 1171-2022 Automobile paint protection film 2022-10-01

194 QC/T 804-2022 Instrument panel assembly and console assembly for passenger cars QCT 804-2014 2022-10-01

195 QC/T 1016-2022 Door trim panel assembly for passenger cars QC/T 1016-2015 2022-10-01

196 QC/T 768-2022 Coach toilet QC/T 768-2006 2022-10-01

197 QC/T 580-2022 Mounting dimensions of automobile transmission assembly QCT 580-1999 2022-10-01

198 QC/T 1172-2022 Performance requirements and test methods for vehicle air brake unit exhaust muffler 2022-10-01

199 QC/T 237-2022 Bench test methods for the performance of automobile parking brake QC/T 237-1997 2022-10-01

200 QC/T 1173-2022 Road vehicles - Spark-plugs application test methods 2022-10-01

201 QC/T 1174-2022 High voltage fuse for electric vehicles 2022-10-01

202 QC/T 1175-2022 High voltage contactor for electric vehicles 2022-10-01

203 QC/T 1176-2022 Evaporator for automotive air conditioning 2022-10-01

204 QC/T 1177-2022 Condenser for automotive air conditioning 2022-10-01

205 QC/T 633-2022 The seats of passenger vehicles QC/T 633-2009 2022-10-01

206 QC/T 80-2022 Road vehicles - Polyamide (PA) tubing for air braking systems QC/T 80-2011 2022-10-01

207 QC/T 1178-2022 Motor vehicle and towed vehicle - Pneumatic braking system - Tapped and male fitting 2022-10-01

208 QC/T 1179-2022 Specifications for automobile wheel bolts 2022-10-01

209 QC/T 869-2022 Short-cycle drawn arc welding stud QC/T 869-2011 2022-10-01

210 QC/T 870-2022 Double end studs bm=1.25 d QC/T 870-2011 2022-10-01

211 QC/T 871-2022 Double end studs bm=2d QC/T 871-2011 2022-10-01

212 QC/T 598-2022 Bearing face projection weld bolts QC/T 598-1999 2022-10-01

213 QC/T 599-2022 Overhead projection weld bolts QC/T 599-2013 2022-10-01

214 QC/T 624-2022 Rubber plugs QC/T 624-2013 2022-10-01

215 QC/T 603-2022 A-type clips QC/T 603-1999 2022-10-01

216 QC/T 604-2022 B-type clips QC/T 604-1999 2022-10-01

217 QC/T 605-2022 C-type clips QC/T 605-1999 2022-10-01

218 QC/T 606-2022 H-type clips QC/T 606-1999 2022-10-01

219 QC/T 618-2022 Specifications for plastic expansion nut QC/T 618-2013 2022-10-01

220 QC/T 928-2022 Plastic cable and tubing clips with interfix hole QC/T 928-2013 2022-10-01

221 QC/T 929-2022 Plastic cable and tubing clips with side-fix hole QC/T 929-2013 2022-10-01



Foreword



Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.



This document is drafted in accordance with the rules given in GB/T 1.1-2020 Directives for standardization - Part 1: Rules for the structure and drafting of standardizing documents.



This document was proposed by and is under the jurisdiction of SAC/TC 114 National Technical Committee of Auto Standardization of Standardization Administration of China.



Motor vehicle and towed vehicle - Pneumatic braking system - Tapped and male fitting



1 Scope



This document specifies the main types and dimensions of base tapped and male fitting in pneumatic braking systems of motor vehicle and towed vehicle.



2 Normative references



N/A.



3 Terms and definitions



None.



4 Type and dimension



4.1 Straight thread



The type and dimension of straight thread hole (tapped fitting) are shown in Figure 1 and Table 1 respectively. The type and dimension of male fitting are as shown in Figure 2 and Table 2 respectively.

Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Type and dimension

附件：
45项汽车行业标准编号、标准名称和实施日期
序号 标准编号 标准名称 被代替标准编号 实施日期
177 QC/T 1157-2022 汽车产品单位产量综合能耗计算方法 2022-10-01
178 QC/T 1158-2022 汽车产品单位产量综合水耗计算方法 2022-10-01
179 QC/T 1159-2022 汽车行业绿色供应链管理评价规范 2022-10-01
180 QC/T 1160-2022 汽车行业整车制造绿色工厂评价导则 2022-10-01
181 QC/T 1161-2022 绿色设计产品评价技术规范汽车 2022-10-01
182 QC/T 1162-2022 汽车外饰件用蜂窝夹层结构制品 2022-10-01
183 QC/T 1163-2022 汽车柴油机选择性催化还原 ( SCR )系统用还原剂过滤器 2022-10-01
184 QC/T 1164-2022 汽车用天然气滤清器 2022-10-01
185 QC/T 1165-2022 汽油乘用车炭罐用空气滤清器 2022-10-01
186 QC/T 1166-2022 汽车用流媒体后视镜 2022-10-01
187 QC/T 1167-2022 乘用车行车制动器噪声台架试验方法 2022-10-01
188 QC/T 1168-2022 汽车用电动空气压缩机性能要求及台架试验方法 2022-10-01
189 QC/T 463-2022 汽车液力变矩器总成技术要求和台架试验方法 QC/T 29033- 1991
QC/T557- 1999
QC/T 463- 1999 2022-10-01
190 QC/T 792-2022 电动摩托车和电动轻便摩托车驱动用电机及其控制器 QCT 792-2007 2022-10-01
191 QC/T 1169-2022 汽车用液晶仪表 2022-10-01
192 QC/T 1170-2022 汽车玻璃用功能膜 2022-10-01
193 QC/T 1171-2022 汽车漆面保护膜 2022-10-01
194 QC/T 804-2022 乘用车仪表板总成和副仪表板总成 QCT 804-2014 2022-10-01
195 QC/T 1016-2022 乘用车门内饰板总成 QC/T 1016-2015 2022-10-01
196 QC/T 768-2022 客车卫生间 QC/T 768-2006 2022-10-01
197 QC/T 580-2022 汽车变速器总成安装尺寸 QCT 580-1999 2022-10-01
198 QC/T 1172-2022 汽车气压制动部件用排气消音器性能要求及台架试验方法 2022-10-01
199 QC/T 237-2022 汽车驻车制动器性能台架试验方法 QC/T 237-1997 2022-10-01
200 QC/T 1173-2022 道路车辆 火花塞匹配性试验方法 2022-10-01
201 QC/T 1174-2022 电动汽车用高压熔断器 2022-10-01
202 QC/T 1175-2022 电动汽车用高压接触器 2022-10-01
203 QC/T 1176-2022 汽车空调用蒸发器 2022-10-01
204 QC/T 1177-2022 汽车空调用冷凝器 2022-10-01
205 QC/T 633-2022 客车座椅 QC/T 633-2009 2022-10-01
206 QC/T 80-2022 道路车辆 气制动系统用尼龙（聚酰胺）管 QC/T 80-2011 2022-10-01
207 QC/T 1178-2022 汽车和挂车 气压制动系统 螺纹孔和管接头 2022-10-01
208 QC/T 1179-2022 汽车用车轮螺栓技术条件 2022-10-01
209 QC/T 869-2022 短周期弧焊焊接螺柱 QC/T 869-2011 2022-10-01
210 QC/T 870-2022 双头螺柱 bm=l .25d QC/T 870-20 11 2022-10-01
211 QC/T 871-2022 双头螺柱bm=2d QC/T 871-2011 2022-10-01
212 QC/T 598-2022 承面凸焊螺栓 QC/T 598-1999 2022-10-01
213 QC/T 599-2022 端面凸焊螺栓 QC/T 599-2013 2022-10-01
214 QC/T 624-2022 橡胶堵塞 QC/T 624-2013 2022-10-01
215 QC/T 603-2022 A型卡扣 QC/T 603-1999 2022-10-01
216 QC/T 604-2022 B型卡扣 QC/T 604-1999 2022-10-01
217 QC/T 605-2022 C 型卡扣 QC/T 605-1999 2022-10-01
218 QC/T 606-2022 H型卡扣 QC/T 606-1999 2022-10-01
219 QC/T 618-2022 嵌装塑料螺母技术条件 QC/T 618-2013 2022-10-01
220 QC/T 928-2022 中间固定式塑料管线夹 QC/T 928-2013 2022-10-01
221 QC/T 929-2022 一端固定式塑料管线夹 QC/T 929-2013 2022-10-01

目次

前言 i
1 范围 1
2 规范性引用文件 1
3 术语和定义 1
4 型式和尺寸 1


前言

本文件按照GB/T 1.1-2020《标准化工作导则 第1部分;标准化文件的结构和起草规则》的规定起草。

本文件由全国汽车标准化技术委员会(SAC/TC 114)提出并归口。

汽车和挂车 气压制动系统
螺纹孔和管接头

1 范围

本文件规定了汽车和挂车气压制动系统中基体螺纹孔和管接头的主要型式和尺寸。

2 规范性引用文件

本文件没有规范性引用文件。

3 术语和定义

本文件没有需要界定的术语和定义。

4 型式和尺寸

4.1 直螺纹

直螺纹孔的型式见图1，尺寸见表1。管接头的型式见图2，尺寸见表2。