![]() |
中标分类
行业分类
ICS分类
最新标准
|
登录注册 |
您的位置: 标准明细 |
This standard replaces YD/T 1582-2007 and YDC 020-2003, and the following technical deviations have been made with respect to YD/T 1582-2007 and YDC 020-2003 (the previous edition): — 2GHz, 800MHz in YD/T 1582-2007 and YDC 020-2003 is modified to 800MHz/2GHz; — The identification for the degree of consistency to the International Standard is supplemented on cover page. This standard is one of the series standards of 800MHz/2GHz cdma2000 Digital Cellular Mobile Communication Network Air Interface, and the structure and names of this series standards are as follows: — YD/T 1556-2007 Technical Specification of Base Station Subsystem (BSS) for 2GHz cdma2000 Digital Cellular Mobile Communication Network Equipment — YD/T 1558-2007 Technical Requirements of Mobile Station for 2GHz CDMA2000 Digital Cellular Mobile Communication Network — YD/T 1580-2007 Technical Specification for 2GHz cdma2000 Digital Cellular Mobile Communication Networks: Physical Layer of Air Interface — YD/T 1581-2010 Technical Specification for 800MHz/2GHz cdma2000 Digital Cellular Mobile Communication Network: Medium Access Control (MAC) of Air Interface — YD/T 1582-2010 2GHz cdma2000 Digital Cellular Mobile Communication Networks: Signaling Link Access Control (LAC) of Air Interface Specification — YD/T 1583-2010 800MHz/2GHz cdma2000 Digital Cellular Mobile Communication Networks: Upper Layer (Layer 3) Signaling of Air Interface Specification — YD/T 1573-2007 Test Specification of Base Station Subsystem (BSS) for 2GHz cdma2000 Digital Cellular Mobile Communication Network — YD/T 1576.1-2007 Testing Methods for 2GHz cdma2000 Digital Cellular Mobile Communication Network Equipment: Mobile Station — Part I Minimum Standard Function and Performance — YD/T 1576.2-2007 Testing Methods for 2GHz cdma2000 Digital Cellular Mobile Communication Network Equipment: Mobile Station — Part II Protocol Conformance Test — YD/T 1576.3-2007 Testing Methods for 2GHz cdma2000 Digital Cellular Mobile Communication Network Equipment: Mobile Station — Part III Protocol Compatibility Test This standard is identical with the International Standard 3GPP2 C.S0004-A v6.0 Signaling Link Access Control (LAC) Standard for cdma2000 Spread Spectrum Systems. Annex A of this standard is normative. This standard was proposed and prepared by China Communications Standards Association. Drafting organization of this standard: China Academy of Telecommunication Research of MIIT. Chief drafting staff of this standard: Guo Jinjun, Yan Di, Du Ying and Gong Daning. This standard was issued in May, 2007 as first edition, and first revised in December, 2010. Technical Specification for 800MHz/2GHz cdma2000 Digital Cellular Mobile Communication Network: Signaling Link Access Control (LAC) of Air Interface 1 Scope This standard specifies the Layer 2 Link Access Control (LAC) signaling protocol architecture and functionality. This standard is applicable to 800MHz/2GHz cdma2000 digital cellular mobile communication network system. 2 Normative References The following normative document contains provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies. CCITT Recommendation E.212, Identification Plan For Land Mobile Stations, 1988 3 Definitions 3.1 Definitions 3.1.1 Access Attempt The entire process of sending one message and receiving (or failing to receive) an acknowledgment for that message, consisting of one or more access sub-attempts. See also Access Probe, Access Probe Sequence, and Access Sub-attempt. 3.1.2 Access Probe One Access Channel transmission consisting of a preamble and a message. The transmission is an integer number of frames in length and transmits one Access Channel message. See also Access Probe Sequence, Access Sub-attempt, and Access Attempt. 3.1.3 Access Probe Sequence A sequence of one or more access probes on the Access Channel. Other than the reported pilot information, the same Access Channel message content is transmitted in every access probe of an access sub-attempt. See also Access Probe, Access Sub-attempt, and Access Attempt. 3.1.4 Access Sub-attempt A sequence of one or more access probe sequences on the Access Channel transmitted to one pilot, containing the same message content other than the reported pilot information. See also Access Probe, Access Probe Sequence, and Access Attempt. 3.1.5 ARQ See Automatic Repeat Request. 3.1.6 Assured Mode Mode of delivery that guarantees that a PDU will be delivered to the peer. A PDU sent in assured mode is retransmitted by the LAC Sublayer, up to a maximum number of retransmissions, until the LAC entity at the sender receives an acknowledgement for the PDU. See also Confirmation of Delivery. 3.1.7 Automatic Repeat Request (ARQ) Technique for providing reliable delivery of signals between communicating stations which involves autonomous retransmission of the signals and transmission of acknowledgments until implicit or explicit confirmation of delivery is received. 3.1.8 Broadcast channel When the channel name is written with lower case letters, it refers to the logical channel on which system overhead information is transmitted by the base station. The logical “broadcast channel” can be mapped to the physical Paging Channel or to the physical Broadcast Channel. 3.1.9 Call History Parameter (COUNT) A modulo-1 64 event counter maintained by the mobile station and Authentication Center that is used for clone detection. 3.1.10 Confirmation of Delivery A notification sent by the LAC Sublayer to Layer 3 at the sender, when the LAC entity at the sender receives the acknowledgment for a specific PDU sent in assured mode. 3.1.11 Full TMSI The combination of TMSI_ZONE and TMSI_CODE. The full TMSI is a globally unique address for the mobile station. 3.1.12 IMSI_O Operational value of IMSI (either IMSI_M or IMSI_T) used by the mobile station for operation with the base station. 3.1.13 IMSI_S A 10-digit number derived from the IMSI that is encoded as a 34-bit valu. IMSI_S generally corresponds to the last 10 digits of the IMSI. 3.1.14 IMSI_S1 A 24-bit value that corresponds to the last 7 digits of IMSI_S. 3.1.15 IMSI_T True IMSI not associated with MIN. Could be 15 digits or fewer. 3.1.16 LAC PDU LAC protocol data unit transferred between peer Utility Sublayers on the mobile station and the base station. 3.1.17 Link Access Control (LAC) Sublayer The LAC Sublayer is the upper sublayer of Layer 2. It implements a data link protocol that provides for the correct transport and delivery of signaling messages generated by Layer 3. The LAC Sublayer makes use of the services provided by the Lower Layers (Layer 1 and the MAC Sublayer). 3.1.18 Logical Channel A communication path between stations, described in terms of the intended use of, and access to, the transferred data, and direction of transfer. A logical channel can be “mapped” to and from one or more physical channels. In this document, channel names beginning with lowercase letters specify logical channels. 3.1.19 Lower Layers In this document, layers below the LAC Sublayer (e.g., Layer 1 and the MAC Sublayer). 3.1.20 Mapping In this context, the technique for forming associations between logical and physical channels. 3.1.21 Mini PDU A PDU that carries a Layer 3 mini message. The total length of a mini PDU is 48 bits. A mini PDU may not be fragmented, and is carried in a 5 ms physical frame. See also Regular PDU. 3.1.22 MCC (Mobile Country Code) A part of the E.212 IMSI identifying the home country. 3.1.23 MNC (Mobile Network Code) A part of the E.212 IMSI identifying the home network within the home country. 3.1.24 MSIN (National Mobile Station Identity) A part of the E.212 MSIN identifying the mobile station within its home network 3.1.25 Multiplex Layer Protocol Layer situated between Layer 2 and Layer 1 on dedicated channels that is responsible for multiplexing Layer 2 SDUs from multiple sources (user traffic, such as voice or data packets, and signaling traffic) onto the same physical channel, according to priority and QoS criteria. 3.1.26 NMSI A part of the E.212 IMSI identifying the mobile station within its home country. The NMSI consists of the MNC and the MSIN. 3.1.27 Physical Channel A communication path between stations, described in terms of the radio characteristics such as coding, power control policies, etc. In this document, channel names beginning with uppercase letters specify physical channels. 3.1.29 Primitive An atomic, well-defined conceptual method of transferring data and control information between two adjacent layers and sublayers. It is conventionally represented as a function invocation, with the data and control information passed as parameters. 3.1.29 Protocol Data Unit (PDU) Encapsulated data communicated between peer layers on the mobile station and the base station. 3.1.30 Protocol Stack Conceptual model of the layered architecture for communication protocols (see Layering) in which layers within a station are represented in the order of their numeric designation and requiring that transferred data be processed sequentially by each layer, in the order of their representation. Graphically, the “stack” is drawn vertically, with the layer having the lowest numeric designation at the base. 3.1.31 SAR Segmentation and Reassembly. 3.1.32 SDU See Service Data Unit. 3.2 Conceptual Model for the LAC Sublayer The layers, sublayers, SAPs, primitives and parameters are abstract modeling constructs, and thus should not be interpreted as implementation requirements. However, the observable behavior of base stations and mobile stations compliant with this specification should be consistent with the interactions described via the primitives and the other modeling constructs mentioned above. LAC signaling for cdma2000 is modeled as follows: • Protocol Layers. The LAC Sublayer provides services to Layer 3. SDUs are passed between Layer 3 and the LAC Sublayer. The LAC Sublayer provides the proper encapsulation of the SDUs into LAC PDUs, which are subject to segmentation and reassembly and are transferred as encapsulated PDU fragments to the MAC Sublayer. • Sublayers. Processing within the LAC Sublayer is done sequentially, with processing entities passing the partially formed LAC PDU to each other in a well established order. • Logical Channels. SDUs and PDUs are processed and transferred along functional paths, without the need for the Upper Layers to be aware of the radio characteristics of the physical channels. 3.2.1 General Architecture The general architecture is presented in Figure 1. Figure 1 cdma2000 Signaling – General Architecture 3.2.2 Protocol Sublayers As a generated or received data unit traverses the protocol stack, it is processed by various protocol sublayers in sequence. Each sublayer processes only specific fields of the data unit that are associated with the sublayer-defined functionality. For example, the ARQ Sublayer operates only on the acknowledgment-related fields, and carries out duplicate detection and retransmission functions. The general processing of data units by the LAC Sublayer and its sublayers is shown in Figure 2. Foreword II 1 Scope 2 Normative References 3 Definitions 3.1 Definitions 3.2 Conceptual Model for the LAC Sublayer 4 Moble Station Requirements 4.1 Common Channel Operation 4.2 Dedicated Channel Operation 5 Base Station Requirements 5.1 Common Channel Operation 5.2 Dedicated Channel Operation Annex A (Normative) Timers and Constants 1 范围 本标准规定了层2链路接入控制(LAC)的信令协议结构和功能。 本标准适用于800MHz/2GHz cdma2000 字蜂窝移动通信系统。 2 规范性引用文件 下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件,其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准。然而,鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件,其最新版本适用于本标准。 CCITT Recommendation E.212,Identification Plan For Land Mobile Stations,1988. 3 定义 3.1定义 3.1.1 Access Attempt(接入尝试) 发送一个消息并接收(或者未接收到)这个消息的证实的整个过程,包含了一个或者多个Access Sub-attempt(接入子尝试)过程。参见Access Probe、Access Probe Sequence和Access Sub-attempt。 3.1.2 Access Probe(接入试探) 包含了一个Preamble(前导)和一个消息的接入信道发送过程。在长度上,发送整数个帧,在内容上,发送了一条接入信道消息。参见Access Probe Sequence、Access Sub-attempt和Access Attempt。 3.1.3 Access Probe Sequence(接入试探序列) 接入信道上包含了一个人或多个接入试探的一个序列。除了导频报告信息,其余内容相同的接入信道消息在每一个接入子尝试所对应的接入试探中被发送。参见Access Probe、Access Sub-attempt和Access Attempt。 3.1.4 Access Sub-attempt(接入子试探) 接入信道上包含了一个或多个接入试探序列的一个序列。这些接入试探序列对应于一个导频信道,除导频报告信息以外,它们包含了相同的消息内容。 3.1.5 ARQ 见Automatic Repeat Request。 3.1.6 Assured Mode(确认模式) 指这样一种传送方式:传送保证PDU被交付到对等层。一个以确认模式发送的PDU将在一个最大重发次数的限制下被LAC层重发,直到发送方的LAC层实体收到这个PDU的一个证实。参见Confirmation of Delivery。 3.1.7 Automatic Repeat Request(ARQ)(自动重发请求) 用来提供通信各方之间信令的可靠传输的技术,引入了信令的自动重发以及发送证实的机制,直到收到显式或隐式的传送解证实。 3.1.8 Broadcast channel(广播信道) 当信道名称用小写字母表示时,指基站用来发送总体消息的逻辑信道,逻辑概念.上的“Broadcast Channel”可以被映射到物理上的寻呼信道或者物理上的广播信道。 3.1.9 Call History Parameter(COUNT)(呼叫历史参数) 由移动台和鉴权中心维护的一个模64的事件计数器,用来进行复制检测。 3.1.10 Confirmation of Delivery(传送证实) 在确认模式下,当发送方LAC层实体收到某个PDU的发送证实时,发送方LAC子层发送给本方层3的一个通知。 3.1.11 Full TMSI 包括TMSI_ZONE和TMSI_CODE,Full TMSI是移动台在全世界内独一无二的地址。 3.1.12 IMSI_O 可操作的IMSI值(可以是IMSI_M或者IMSI_T),移动台使用它来进行与基站的各种操作。 3.1.13 IMSI_S 来自IMSI的一个十位十进制数,被编码成一个34bit的二进制值。IMSI_S一般与IMSI的最后10个数字相关。 3.1.14 IMSI_ S1 和IMSI_S最后7个数字相关的一个24bit的二进制值。 3.1.15 IMSI _T 真IMSI,与MIN无关。可能有15个或者少于15个数字。 3.1.16 LAC PDU LAC层协议数据单元,在移动台和基站的对等功能子层之间传递。 3.1.17 Link Access Control(LAC)Sublayer(链路访问控制子层) LAC子层是层2的上部子层,它实现的数据链路协议提供了层3产生的信令消息的正确发送和交付。LAC子层使用了低层(层2和MAC子层)所提供的服务。 3.1.18 Logical Channel(逻辑信道) 站/台间的通路径,以传输数据的预期用途及访问方式、传输方向来描述。一个逻辑信道可以被“映射”至一个或多个物理信道,或者说由一个或者多个物理信道映射成一个逻辑信道。在这个文档中以小写开头的信道名表示逻辑信道。 3.1.19 Lower Layers(低层) 在这里指LAC子层以下的各层(即层1和MAC子层)。 3.1.20 Mapping 在这里指用来在逻辑信道和物理信道之间建立联系的技术。 3.1.21 Mini PDU 一个承载了层3mini消息的PDU,mini PDU的总长度是48bit。一个mini PDU不能够被拆开,并且在5ms帧中传送。参见规则PDU。 3.1.22 MCC(移动国家码) E.212 IMSI的一部分,确定了所在国家。 3.1.23 MNC(移动网络码) E.212 IMSI的一部分,确定了本国内所在网络。 3.1.24 MSIN(移动台识别号) E.212 IMSI的一部分,确定了所在网络中的一个移动台。 3.1.25 Multiplex Layer(复用层) 处于专用信道层1和层2的协议层,它根据QoS标准和优先级将多个消息来源的层2 SDU(用户数据,如数据包或语音数据以及信令)复用到相同的物理信道中。 3.1.26 NMSI(国家移动台识别号) E.212 IMSI的一部分,在其所在国家内确定了移动台。NMSI包括了MNC和MSIN。 3.1.27 Physical Channel(物理信道) 站/台间的通信路径,依据码型、功率控制方式等无线参数描述。在这个文件中,以大写字母开头的信道名指物理信道。 3.1.28 Primitive(原语) 用来在两个层和子层之间传送数据和控制信息的一个不可再分、明确定义的概念方法。常常以一个函数调用的形式表述,用参数表示待传的数据和控制信息。 3.1.29 Protocol Data Unit(PDU)(协议数据单元) 在移动台和基站的对等层之间传送已封装的数据。 3.1.30 Protocol Stack(协议栈) 通信协议的分层结构的一种概念模型(见Layering)。在这种结构中,一个站/台的的各个层按数字序号表示,而传送的数据必须按序号顺序被各层处理。从图形上看,这个“栈”是个纵向结构,指定最小序号的层处于最底部。 3.1.31 SAR 分段和重组(Segmentation and Reassembly)。 3.1.32 SDU 见Service Data Unit。 3.1.33 SID(系统识别号) 惟一确定了一个蜂窝系统或PCS系统的数字。 3.2 LAC子层概念模型 层、子层、SAP、原语和参数都是抽象的模型结构,因此不能被说明成为具体的实现条件。然而,遵循这些规范的基站和移动台的可见行为必须与以下原语中所描述的过程以及以上提及的其他模型结构相一致。 cdma2000中LAC层的信令如下: 协议层。LAC子层向层3提供服务,其SDU在层3和LAC子层之间传递。LAC子层通过适当的封装将SDU变成将被分段和重组的LAC PDU,这些PDU以封装PDU片段的形式传递给MAC子层。 子层。LAC子层中的处理有固定的顺序,按照这个严格的顺序,各处理实体将部分构造好的LAC PDU传递给另外的实体。 逻辑信道。在逻辑信道中,SDU和PDU沿一条以功能划分路径被处理和传递,而不需要上层知道物理信道的无线特性。 3.2.1 概要结构 图1示出了cdma2000信令的概要结构。 图1 cdma2000信令概要结构 3.2.2 协议子层 当产生或收到的一个数据单元通过协议栈时,它将被多个协议子层按顺序处理。每一个子层仅处理这个数据单元的某一些与这个子层所定义的功能相关的字段。例如,ARQ子层仅处理与证实有关联的字段,并执行复制检测和重发的功能。 图2示出了数据单元在LAC层及其子层中的整体处理过程。 图2 LAC数据单元处理过程 3.2.3 逻辑信道 层3和LAC子层在逻辑信道发送并接收信令信息,这样它们不需要关心层1所使用的物理信道的无线特性。一个逻辑信道建立的时候通常是不分方向的,但是在大多数情况下一个逻辑信道都和另一个传送相似业务的逻辑信道在功能上组合。cdma2000系统使用以下类型的逻辑信道来承载信息: f-csch/r-csch(前/反射公共信令信道) f-dsch/r-dsch(前/反向专用信令信道) 逻辑信道按以下标准被划分:是向一个还是多个目的发送信息:发送的信息是信令还是用户数据;是前向发送还是反向发送以及其他的标准。逻辑信道按以下目的定义: 同步(Synchronization)。 广播(Broadcast)。 通用信令(General Signaling(包括寻呼))。 接(Access)。 专用信令(Dedicated Signaling)。 可以配置多个同名的逻辑信道。 由于逻辑信道上的业务最终是通过一个或多个物理信道发送的,所以逻辑信道和物理信道之间必须建立起某种对应关系。这种对应关系称为映射,一个逻辑信道可能永久地独占一个物理信道(如同步信道),也可能是暂时的,但仍然是独占一个物理信道((如连续的r-csch接入试探序列能在不同的物理接入信道上被发送),还可能和另外的逻辑信道共享一条物理信道(需要有复用功能才能进行这种映射,例如按PDU by PDU原理)。 在某些情况中,一个逻辑信道可以被映射到另一个逻辑信道上。这两个(或多个)信道“融合”成一个有效的逻辑信道,这个逻辑信道可以传输不同的业务数据类型(例如逻辑广播信道和普通前向信令信道都映射到一个传输信令信息的公共逻辑信道上)。因为逻辑信道只能同时发送一个PDU,层3必须有一个序列化的机制来保证发送某一确定帧。 图3和图4分别示出了cdma2000前向和反向链路的逻辑信道。所有的映射类型在这里都有例子:永久的和临时的逻辑—物理映射(例如反向接入信道)、复用的逻辑—物理映射(前向和反向的dsch和dtch之间)和逻辑—逻辑映射(广播信道和通用信令信道)。 3.2.4 接口 3.2.4.1 与层3的接口 层3和层2之间的接口是一个服务接入点(SAP)。在服务接入点上,层3和层2通过一组原语交换服务数据单元(SDU)和以消息控制和状态块格式构造的接口控制信息。通用的原语调用格式如下: L2- 可选参数data_unit和MCSB分别表示将要交换的SDU和消息控制和状态块。 3.2.4.1.1 消息控制及状态块(MCSB) 消息控制及状态块是定义的各原语所需的一个参数块,包括每条层3消息(LAC SDU)的相关信息,指示了消息可能的操作方法,消息将怎样被LAC子层或者MAC子层中的某一层或两层进行处理(在发送时),曾被LAC子层或者MAC子层中的其中一层或两层按怎样处理的。在发送时,MCSB从层3取得并被SAR子层丢弃。当接收时,MCSB由SAR子层产生,通过协议栈到达层3。MCSB是一个概念上的结构,这个文件不会对其进行具体说明,不过可以想像MCSB将包括如下字段: 图3 前向逻辑信道结构 MSG _TAG。如果这条消息是先前接收的一条消息的响应,前一条消息的MSG_TYPE也应该是被保存起来的。 SDU的长度。 寻呼记录长度参数,即:一条指定移动台地址的普通寻呼消息中的SDU_INCLUDED字段;一条指定移动台地址的通用寻呼消息中的EXT_MS_SDU_LENGTH_INCL和EXT_MS_SDU_LENGTH字段;在普通寻呼消息或者通用寻呼消息中发送的增强广播记录中的EXT_BCAST_SDU_LENGTH_IND和EXT_BCAST_SDU_LENGTH字段。 一个与消息相关的单一实例识别号,这个识别号使传送到/未传送到的通知和恢复程序中所涉及的各条消息能够被识别。 当前消息是否需要在LAC子层进行证实(即传送是使用有确认模式还是无确认模式) 是否需要消息到达的通知。 消息地址ID。 图4 反向逻辑信道结构 送到层3的消息是否是重复消息(当然是在LAC子层不丢弃重复消息的情况下)。 鉴权程序所需要的数据(例如起呼消息的CHARi字段)。 相关SDU的分类(例如登记、起呼),在LAC子层中能检测到当前传输SDU的类型的处理过程中得到。 逻辑信道的加密状态:加密模式、加密序列号和未加密SDU的加密8bit CRC。 接收消息的第一个或最后一个比特所在帧的相关CDMA系统时间。 给LAC子层的传输指令,如调度指示说明了怎样发送一个具有某一个相关优先级的消息(先发、后发或者需要中断别的消息的发送),又如一个关于消息监视的指令等。 由LAC发出的非正常情况指示。 当前收到的PDU是否需要层2证实的一个指示。 收到PDU的一个证实已发送并被证实的一个指示。 当f-csch上收到一个PDU并处理其ARQ字段时,在r-csch上发送的一个PDU的接入尝试可能因此而终止,有一个指使字段将指示其是否终止。 消息发送的物理信道。LAC层使用这个信息来给要调用的MAC层原语的“channel_type”参数赋值。 一个紧急呼叫指示。当移动台判定了一条消息属于紧急呼叫,将把紧急呼叫指示打开。 3.2.4.1.2 接口原语 以下原语是为层2和层3间的通信定义的: 名称:L2-Data.Request; 类型:请求; 方向:从层3到层2; 参数:SDU,MCSB; 作用:将SDU交付给层2,准备通过空中接口发送。 名称:L2-Data.Confirm; 类型:确认; 方向:从层2到层3; 参数:MCSB; 作用:在收到了指定(在MCSB中)的由层3发送的SDU后由层2接收方进行确认。 名称:L2-Data.Indication; 类型:指示; 方向:从层2到层3; 参数:SDU,MCSB; 作用:收到的SDU被发给层3。 名称:L2-Condition.Notification; 类型:指示; 方向:从层2到层3; 参数:MCSB; 作用:层3收到层2检测到的相关事件的通知(如非正常情况)。 名称:L2-Supervision.Request; 类型:请求; 方向:从层3到层2; 参数:MCSB; 作用:层2执行层3指定的一个控制命令(例如,一个停止消息重传的命令或复位消息序列号、证实序列号以及用于消息复制检测的计时器的指令)。 3.2.4.2 与MAC子层的接口 LAC子层和MAC子层之间的接口是一个服务接入点(SAP)。有服务接入点上,LAC子层和MAC子层通过一组原语交换服务数据单元(SDU)和以消息控制和状态块格式构造的接口控制信息。通用的原语调用格式如下: MAC- MAC子层的收发并不保证消息的到达,也不保证消息不被重复接收和按顺序到达。一个发送给MAC子层的LAC PDU或者封装的PDU片段立即被发送,同样,一个接收的LAC PDU或者PDU片段立即被交付给LAC子层,除非另外请求,发送和交付都只进行一次。MAC子层以与LAC子层发送时同样的顺序传送封装PDU或者PDU片段;也以接收同样的顺序向LAC子层递交封装PDU或者PDU片段,如果要改变发送顺序,也需另行请求。如果低层检测到封装PDU中有错误,则这个PDU不会交付给上层。 3.2.4.2.1 保留 (暂空) 3.2.4.2.2 接口原语 以下原语是为LAC子层和MAC子层间的通信定义的。 名称: MAC-SDUReady.Request(channel_type,size,P,seqno,scheduling_hint); 类型:请求; 方向:从LAC子层到MAC子层; 作用:对这条原语的调用表示了一个封装PDU的多个片段已经可使用的一系列通知,同时还可以提供发送这些片段的必要的调度信息。 名称:MAC-SDUReady Response(access_mode); 类型:响应; 方向:从MAC子层到LAC子层; 作用:LAC子层得到MAC子层的一条通知,说明MAC子层将要以何种接入模式发送最近的一条MAC_SDUReady.Request所对应的PDU。 名称:MAC-Data.Request(channel_type,data,size); 类型:请求; 方向:从LAC子层到MAC子层; 作用:请求封装PDU的片段从空中接口发送。如果调用时没有PDU片段,并且size参数设置为“0”则表示LAC子层没有更多的数据需要传送。 名称:MAC-Data.Indication(channel_id,channel_type,data,size,system_time,physical_channel_id); 类型:指示; 方向:从MAC子层到LAC子层; 作用:将接收的PDU发送到LAC子层。没有压缩的PDU片段的调用可以用做信号接收错误。 名称:MAC-Availability.Indication(channel_type,max_size,system_time); 类型:指示; 方向:从MAC子层到LAC子层; 作用:LAC子层接到低层的通知,说明了封装PDU片段长度最大,使其能在相邻的较低层的传输单元(例如帧)中发送。调用同时给出了定时的边界(例如时隙的起始和结束位置)。 名称:MAC-AccessFailure.Indication(reason,acceptable_rate); 类型:指示; 方向:MAC子层到LAC子层; 作用:LAC 子层收到MAC子层的通知,声明-一个PDU不能在r-csch上被发送出。 参数定义: channel_type应该被设置为“5ms FCH/DCCH 帧”、“20ms FCH/DCCH帧”、“F-CCCH帧”、“F-BCCH帧”、“R-CCCH帧”、“F-PCH 帧”、“F-SYNC帧”、“R-ACH帧”或者“ENHANCEDACCESS帧”。 size应该被设置为封装PDU或者封装PDU的片段的比特数(当有data参数时)。 P应该被设置为R-ACH、R-EACH 和R-CCCH上持续测试的值。 seqno应该被设置为R-ACH,R-EACH.上R-CCCH当前接入子试探中的接入试探计数的值。 scheduling-hint用来向MAC层的复用子层指示怎样设置各种类型的业务的优先权,包括封装PDU的片段和其他类型的复用业务。 access_ mode是MAC子层传输一个PDU所使用的接入模式(基本接入模式或者保留接入模式)。 data封装PDU的一个片段。 system_time应该被设置为物理层收到物理层帧中包含了信息内容的第-一个比特的时间或将要发送一个帧的时间。 physical_channel_id被设置为物理信道的惟一的标识符,标识数据是在哪个信道上被接收。 max_ size应该被设置为能和MAC-Data.Request原语匹配的size参数的最大可接受值。 reason被设置为“Timer Expired”、“Loss of Channel”或者“Insufficient Transmission Rate”。 acceptable_rate被设置为传输时能够使用的最大瞬时传输率,不论reason 是否被设置为“Insufficien Transmission Rate”。 当LAC子层有一个PDU需要被发送时,它调用MAC-SDUReady.Request原语,并传递封装PDU的大小和其他信息,如类型、序列号、连续门限或者调度所需的信息(如优先权)。MAC子层使用这些信息来执行这次发送。如果在MAC子层完成当前MAC-SDUReady.Request原语所指定的PDU之前又收到后一条MAC-SDUReady.Request原语,则新的调用将覆盖先前的一个调用,即前面一个PDU的传输披中断而开始发送一个新的PDU。对于每一个后续的物理层可用传输单元(例如帧),MAC子层调用MAC-Availability.Indication原语,说明了这个传输单元可以携带的比特数。LAC子层立即以MAC-Data.Request原语响应,发送一个长度小于或等于MAC-Availability.Indication原语指示大小的数据包。如果收到一个MAC-Availability.Indication原语后已经没有可以发送的数据,LAC子层以“0”为size参数调用MAC-Data.Request原语,这样通知MAC子层PDU的传输结束。 在接收时,当收到需要交付的封装PDU片段,MAC子层就调用MAC-Data.Indication原语通知LAC子层。 3.2.5 功能描述 在专用信道上,LAC子层执行下面的功能: 向层3的对等实体发送SDU,当需要保证可靠性时,使用ARQ技术。参见下面的ARQ子层。 构造并检测构造好的PDU的有效性,这些PDU用作正确地承载SDU。参见下面的功能子层。 拆分封装的PDU为多个封装的PDU片段,使这些片段的大小适合在MAC子层的发送。参见下面的SAR子层。 将拆分的封装PDU片段重组为封装PDU,参见下面的SAR子层。 通过“统一查询”鉴权的接入控制1。原则上,公共信道上没有通过鉴权的消息不能够被传递给高层进行处理。参见下面的鉴权子层。 地址控制,用来保证基于地址传送的PDU能够被正确交付,这些地址指定了某个特定移动台。参见下面的地址子层。 1某些鉴权是层3的一个功能,而另一些处于层2。特别地,“global challenge”类型的鉴权是放在层2的,因为它可以被看作与接入有关。具体的实现并不拘泥于这个模型构想。 3.2.5.1r-csch上的操作 图5示出了一个r-csch逻辑信道上LAC子层结构。 图5 协议结构:r-csch 移动台在r-csch发送的消息按以下过程操作: 在服务接入点上,层3调用L2-Data.Request原语,将SDU和相关的MCSB送到LAC子层。 SDU和MCSB首先经过鉴权子层,该层设置移动台鉴权字段并将它们加在SDU上,构造出初始的LAC协议数据单元(PDU)。 初步构造的PDU和MCSB再经过ARQ子层,该层根据MCSB中的信息相应地设置移动台的证实字段,并将它们加在PDU上。 — 如果ARQ子层需要对收到的PDU发送一个证实,并且层3指明对所收到消息没有层3响应,则ARQ子层发送一个仅用作证实的PDU,以响应收到PDU。 — 如果ARQ子层需要对收到的PDU发送一个证实,并且层3指明对所收到消息存在层3响应,则ARQ子层将证实包含在承载层3响应的PDU中发送。 构造的PDU和MCSB再经过地址子层,该层设移动台的地址字段为适当的值再将其加入PDU。 PDU和MCSB再被送至功能子层,该层将MCSB中的MSG_TAG映射为PDU中的MSG_TYPD字段。功能子层进一步构造出移动台的导频测量报告字段并加在PDU上,在每次重发的过程中,旧的导频测量报告字段将被新的字段所取代。PDU接着将被以按需要0~7bit的“0”所填充,使其具有整数个字节加2bit的长度,这些操作完成了PDU的构造。如果其间有错误发生,LAC子层能够使用L2-Condition.Notification原语通知层3。 |
联系我们
|
微信联系客服
![]() |
关于我们 | 联系我们 | 收费付款 | ||
版权所有: 中译悦尔(北京)翻译有限公司 2008-2040 | ||
全国免费电话:800-810-5431 电话:010-8572 5110 传真:010-8581 9515 | ||
Email: bz@bzfyw.com | |
||
本页关键词: | ||
YD/T 1582-2010, YD 1582-2010, YDT 1582-2010, YD/T1582-2010, YD/T 1582, YD/T1582, YD1582-2010, YD 1582, YD1582, YDT1582-2010, YDT 1582, YDT1582 |